Top » Catalog » Print Media, PSA » Vinyl, Opaque » sol-rb428p54
 
0
$0.00
Categories
Print Media, PSA
  Drywall Graphics
  Film, Carrier-less Decal
  PET, Polyester
  Poly, Cloth, Canvas
  PP, Synthetic Paper
  Vinyl, ATV
  Vinyl, B-free Install
  Vinyl, Bus & Transit
  Vinyl, Clear
  Vinyl, Clear Adhesive
  Vinyl, Floor & Carpet
  Vinyl, Flour/Phosphorescent
  Vinyl, Gray Adhesive
  Vinyl, Hi-tack Adhesive
  Vinyl, Holographic
  Vinyl, Light Blockout
  Vinyl, Metalized
  Vinyl, Opaque
  Vinyl, Perforated
  Vinyl, Reflective
  Vinyl, Removable
  Vinyl, Rough Surface
  Vinyl, Semi-rigid
  Vinyl, Translucent
  Vinyl, Vehicle Wrap
  Window Graphics
Manufacturers
Information
Mactac
Rebel RB428P M White 99% Blockout Perm 4mil 54"x150'
[sol-rb428p54]
$0.41 /sq ft.
$275.00
Sq Ft. Price:$0.41
Regular Price:$275.00
Available Options:
Qty:  

RB428P is a 4-mil soft; non-top coated, opaque matte white vinyl coated with an acrylic permanent adhesive. The liner is a 90# SuperFlat™, C2S polycoated that provides excellent lay flat. Designed for moderate term screen and digitally printed graphic applications, indoor and out. The adhesive has a moderate initial tack and builds to a strong permanent bond with good resistance to creep, solvents and heat. Suggested uses include screen-printed labels, decals, markings, point-of-purchase displays and signs for indoor and outdoor use.

DURABILITY:
Five years indoors and up to 3-4 years outdoors. This use-life estimate is based upon accelerated age studies. Please note that exposure to severe temperatures, ultra-violet light and also in tropical, sub-tropical or desert regions will cause more rapid deterioration. This also applies to polluted areas, high altitude and south facing exposure.

RECOMMENDATIONS:
Always test your combination of REBEL products, inks and laminating films prior to commercial use.

  1. Printing Conditions: Print in conditioned pressroom at ±73°F (23°C) and 50% RH. The maximum allowable ink saturation is 270%.
  2. Drying Requirements: Solvent, Eco-solvent and Mild-solvent inkjet prints require 24 - 48 hr. drying time - open to the air. Inks do not dry when printed media is rolled up. The prints must be dry prior to lamination.
  3. Laminating Conditions: If the printed graphic is likely to be exposed to corrosive liquids, smoke, fumes, and highly polluted areas or there is a likelihood of scratching, it is highly recommended to laminate with Permacolor IP7000, CG8000 Series or LF3600 High performance overlaminating films.
  4. Application: Do not use wet application fluids when applying this media unless it is specifically designed for emulsion adhesives. Standard application fluids including soap or detergent in water may cause the adhesive to turn white.
  5. Transportation Conditions: To allow for easy transportation, IMAGin JT5000 series can be rolled up, with the image out, with a minimum diameter of 6 inches (15cm). When the image is not protected by an overlaminate, make sure the print is completely dry and protected in a plastic bag. During transportation or storage, avoid exposing them to extreme temperature

GENERAL PRECAUTION:
The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide. If there are any questions about applications, please contact your MACtac sales representative to discuss your requirements for recommendations. If this is a printed Performance Guide it is an uncontrolled document. Please check the MACtac website for the latest, most up-to-date version.

  WJT Sign Supply is not responsible for typographical or photographical errors.
  Prices are listed in Canadian funds and specifications are subject to change without notice.
  WJT Sign Supply
  1160 Tapscott Road, Unit 7, Scarborough, Ontario, Canada M1X 1E9
  Tel: 905-475-2632
Copyright © 2005 WJT Sign Supply.
Powered by osCommerce